Tylo Sauna Heater Wiring Diagram

Tylo sauna heater wiring diagram. Sauna heater installation connection/wiring diagram checking installation. • the sauna ventilation must comply with the instructions in this manual (see the section called positioning the inlet vent, page 2, the section called positioning the outlet vent, page 2). Tion called connection/wiring diagram, page 7). To restart the heater, let the heater cool and turn the timer down to zero (off), then push the reset button on the bottom of the heater, see diagram 1.

A helo sauna heater elevates the daily sauna experience by adding beautiful design and ingenuity to the heater’s functionality. Connect using wire rated at 75o c. The wires to the terminal block. Wiring diagram for infrared heater example wiring diagram.

Tylo heater specifications model volts/ / phase kw output amps/ /breaker wire mininimum / maximum cubic feet 208/3 6.3 30 / 40 8 320 640 deluxe 11 240/1 10.7 45 / 60 6 320 640 240 volt, 1 phase is standard for houses in north america. For the heater (see the section called connection/wiring diagram, page 8. See diagram 6 for proper connections. When you are buying a tylo sauna heater, you are not just buying a function, you are buying years of development, experience and a relentless strive for perfection.

Ingenuity, simplicity and a love for the good life has been the helo breeding ground for the wide spread reputation of genuine finnish saunas. Tylo sauna heaters are designed with a vertical rock chamber that allows the sauna rocks to be in direct contact with the heating elements (see figure 20). Check the heater’s type identification plate to ensure that the heater is connected to the right voltage. Bench must tuck under the back.

Installation guide user guide loyalty. Tn the event of any problems, please contact the retailer. Use copper supply wire only, suitable for minimum 90 degrees c. 23, 27, 29 wiring diagrams.

Heating elements do not change for voltage changes. Tylö deluxe sauna heater with outside control. 24 hours connection time, 24 hours preselected time. From the heater i have a black, white, and bare wire.

(there are a few exceptions; 5 = rb 30 check the heater's data plate to ensure it is connected to the correct voltage. When mounting the heater, please take note of the following: Install a wooden heater guard to prevent the sauna bather from accidentally touching the sauna heater.

Sauna heater herb bowl/air humidifier bracketsx 4 warning sticker in ten languages bracket screws x 4 connectors x 3 Place the power cord on the ground to the side of the floor; 1 • connect s3 from the right distribution plate to s3 from bench skirt • connect #6 from the distribution plate to #6 from the bench top. Bench must tuck under the back heater guard and.

1 person infrared sauna sain page 2 180521 rev. Lay the heater down with the front facing upwards. Sauna heater installation it is easiest to prepare for installation with the heater lying down. • the position of the sauna heater, control panel, and sensors

The black and white connect to separate terminals on the thermostat switch, the bare goes to the ground nut. 26, 30, 32 wiring diagrams. Karhu pata 60 installation and user manual loyalty. • bench tops can now be fit into place.

This prevents the heater from being removed from the wall. 4 person infrared sauna residence page 13 180521 rev. • locate the electrical switch on the black master control box and ensure the switch is on. Remove the center grille (not needed) and place the stones down in the center chamber only.

To determine the correct wire size, refer to diagram 2. • the sauna ventilation must comply with the instructions in this manual (see the section called positioning the inlet vent, page 5, the section called positioning the outlet vent, page 5). (with sauna heater deluxe and control panel ts ). Tylo heaters are masters of providing a range of climate zones and individual sauna experiences.

I was wondering about the correct way to wire a 240v sauna heater/thermostat in a sauna i have built. To properly install the sauna rocks in the heater, first wash them to remove any dust or dirt. When the heater has been installed, a set screw (l, fig 10) locks it in place on the supporting brackets. Under the house is a 120v/240v gfci.

The heater must be grounded! For the heater (see the section called connection/wiring diagram, page 4. Check the heater’s type identification plate to ensure that the heater is connected to the right voltage. Check the heater’s type identification plate to ensure that the heater is con nected to the right voltage.

Copper wires are generally recommended by contractors and electricians because they are durable, heat resistant, good conductors and will corrode. (with sauna heater deluxe and control panel ts ).